Coprox Logo

Preventative, Remedial & Decorative Waterproofing™


Coprox Cobond

  • Seamless Waterproofing Membrane System for Water Bearing Positive Side Masonry Surfaces
  • Bonding & Keying Agent
  • Additive to Coprox Waterproof Dualcoat
  • Suitable for Brick, Mortar, Screed, Concrete; Cement and Pool Plasters

Waterproofing Instructions

Coprox Cobond mixed with Coprox Masonry Waterproofing is a seamless waterproofing membrane system suitable for waterproofing water bearing positive side masonry surfaces, which are subject to moderate expansion and contraction. These include balconies, copings and the abutments of slabs and walls. It is also ideal for the waterproofing and rejuvenation of pitted and stained swimming pools, ponds, reservoirs and water features.

Coprox Cobond has excellent adhesion properties on dense and smooth surfaces and is suitable for commercial and domestic applications.

Suitable Surfaces
  • Sufficiently aged and cured virgin mortar, screed, concrete and cement or pool plasters of recognised building mix standards.
  • Good quality virgin cement and clay bricks.

If in any doubt as to surface suitability, do a test area first.

Weather Conditions
  • Do not apply to exterior surfaces if rain is imminent, in humid conditions, during high winds or freezing temperatures.
Surface Preparation
  1. Ensure the surfaces are free of any negative moisture. Should this not be the case, the surfaces must first be treated with Coprox Masonry Waterproofing or if necessary, plastered with Coprox Waterproof Cement Additive added to the plaster mix, before proceeding with the application. This applies equally to swimming pools, ponds, reservoirs and water features where high water tables may be present. Surfaces such as boundary and retaining walls must also be treated in this manner before the application commences.
  2. Remove any efflorescence whilst dry using a stiff bristle scrubbing brush.
  3. Where the application is being used for swimming pools, ponds, reservoirs and water features:

Remove algae and oils with a scrubbing brush using:

  • 1 part of hydrochloric acid to 20 parts of water for the entire surface.
  • 1 part of hydrochloric acid to 10 parts of water for the water line and steps.
  •  Neutralize the acid washed surfaces with copious amounts of water.
  • Mop up the neutralized acid wash.

4. Remove dust, dirt and all other foreign matter.

5. Surfaces must be completely dry and free of any moisture before application commences.

  1. Decant 5 litres of Coprox Cobond into a clean plastic container and stir thoroughly.
  2. Sprinkle 5 kg of the desired colour Coprox Masonry Waterproofing slowly into the 5 litres of Coprox Cobond preferably stirring with a mechanical mixing device until smooth and free of lumps. Use immediately.
  3. Stir the solution frequently throughout the application.
First Coat
  1. Apply the first coat to the dry surfaces using a suitable brush. Brush strokes should be applied in one direction to a thickness not exceeding 1,5 mm.
  2. Thoroughly cover depressions, fine cracks and pinholes.
  3. When bridging joints or abutments of slabs and walls, the application should cover the joint by at least 75 mm on either side.
Second Coat
  1. Ideally, the second coat should be applied as soon as the first coat is touch dry, approximately 30 minutes. If the second coat can only be applied later, ensure that the first coat is completely dry and free of any moisture before the second coat is applied.
  2. Apply the second coat at right angles to the first coat, again to a thickness not exceeding 1,5 mm.
  3. Keep the application protected from rain.
  4. Allow the application to dry for at least 48 hours before use.
Coverage: 6 m² per coat (approx.)

1 litre Coprox Cobond:1 kg Coprox Masonry Waterproofing

Filling Swimming Pools, 
Ponds, Reservoirs
Water Features

To minimize foaming when filling swimming pools, ponds, reservoirs and water features for the first time:

  1. Thoroughly hose down the surfaces several times with generous amounts of water 48 hours or more after the application has been completed.
  2. Mop up the foamy water.
  3. Proceed with the filling of clean water.

Should any foam still be present after filling, the foam will dissipate with filtering or with changes of clean water.


Once dry, the application is non-toxic and therefore not harmful to human, animal or plant life. However, the water must be free of any foam and allowed to age sufficiently and treated chemically before introducing fish or plants. Consult your local pet shop or water authority in this regard. In the case of swimming pools, pH levels should be properly maintained. All chemicals should be added via the weir.

Cleaning Tools & Equipment

Use clean water. Product and waste water containing product should not be discharged directly into drains and waterways.


1 litre & 5 litre Plastic Bucket.

Storage & Shelf Life

12 months when stored sealed in a dry place.

Identification & Composition

A white non-flammable styrene/butadiene co-polymer latex liquid.

  • If there is inadequate ventilation a face mask should be worn.
  • Protective gloves and goggles should be worn.
  • Avoid prolonged or repeated skin contact.
  • Keep out of reach of children.
First Aid

  • If swallowed, do not induce vomiting. Drink plenty of water. Seek immediate medical attention.
  • Excessive inhalation of vapour may cause dizziness or headache. Breathe plenty of fresh air.
  • Eye contact - may cause temporary irritation. Flush eyes with plenty of water. If irritation persists, seek medical attention.
  • Skin contact - irritation may be caused by direct or prolonged contact. Wash contact areas with soap and water and apply aqueous cream.

Coprox International (Pty) Ltd has no control over the purpose for which its products are used, stored, prepared and applied. No warranty is therefore given as to its suitability, nor is any warranty, express or implied, given for any damage of whatsoever nature, consequential or otherwise, arising out of the use of its products.